Livarno Z29618-BS Manual de usuario descargar pdf

GR / CY

GB / IE / CYGB / IE / CYGB / IE / CYGB / IE / CYGB / IE / CY GB / IE / CY

GB / IE / CY

protective surround. Then hold the LED work lamp

against a magnetic surface.

Using the LED work lamp

disconnected from a power

supply

j Fully charge the LED work lamp, as described

in the section on “Charging the LED work

lamp”.

j Set the ON / OFF switch

to position I to

switch on the LED work lamp.

j Set the ON / OFF switch

to position 0 to

switch oﬀ the LED work lamp.

of damage.

J CAUTION! DANGER OF

EXPLOSION! Do not operate

the LED work lamp in potentially

explosive environments in which there are

inﬂam mable vapours, gases or dusts.

J The LED work lamp is protected against water

spray. However, the product, mains adapter

and car adapter must never be immersed in

water or other liquids. Failure to observe this

advice will create the risk of electric shock!

Never hang the product near a washbasin,

pond and the like.

J Connect the LED work lamp to a properly

installed mains socket or a suitable cigarette

lighter socket only. The voltages in each case

must comply with information given in the

section “Technical data”.

start to use the LED work lamp again.

Otherwise water could enter the power input

connection socket

if the LED work lamp is

used outdoors.

Use

CAUTION – RISK OF ACCIDENT! If at

all possible, do not use the LED work lamp in a

moving vehicle. If the LED work lamp is used in a

vehicle, it must not be allowed to endanger the

safety of the driver or passengers. Always store

and secure the LED work lamp in such a way that

there is no risk of injury from or damage to the

product, even during full braking.

Note: You can secure the LED work lamp in

place using the hook

or magnetic mount

Clamp the magnetic mount

to the LED’s

Safety instructions

J Always keep children away from

the packaging material. This

product is not a toy.

J Children or persons who lack the knowledge

or experience to use the device or whose

physical, sensory or intellectual capacities are

limited must never be allowed to use the

device without supervision or instruction by a

person responsible for their safety. Children

must never be allowed to play with the device.

J This product is not a toy and should be kept

out of the reach of children. Children are not

aware of the dangers associated with

handling electrical products.

J Do not use the article if you detect any kind

and their opening hours can be

obtained from your local authority.

Defective or exhausted rechargeable batteries

must be recycled in accordance with Directive

2006 / 66 / EC. Return the battery and / or the

device through the appropriate collection facilities.

Improper disposal of

rechargeable batteries can

damage the environment!

Rechargeable batteries must not be disposed of

with the household refuse. They may contain toxic

heavy metals and require to be handled as special

waste. The chemical symbols of heavy metals are:

Cd = cadmium, Hg = mercury, Pb = lead.

free cloth. Use a slightly moist cloth to remove

any stubborn dirt.

Disposal

The packaging is made entirely of

recyclable materials, which you may

dispose of at local recycling facilities.

Contact your local refuse disposal authority for

more details of how to dispose of your worn-out

product.

To help protect the environment,

please dispose of the product properly

when it has reached the end of its

useful life and not in the household

waste. Information on collection points

Fault Possible causes and cures

Charging

takes a

very long

time

When connected to a

cigarette lighter socket:

- Vehicle battery too weak?

Maintenance and cleaning

The product requires no maintenance. The LEDs

cannot be replaced.

J Switch oﬀ and disconnect the product from

the power supply before you clean it.

J Never immerse the product in water or other

liquids.

J Do not use corrosive cleaning agents.

j Clean the product regularly with a dry, ﬂuﬀ-

Troubleshooting

Fault Possible causes and cures

functions

- Mains adapter

or car adapter

is not fully inserted.

Indicator

LED

does not

illuminate

When connected to a

cigarette lighter socket:

- Is the cigarette lighter socket

supplied

with power? Some

cigarette lighter sockets only

supply power with the ignition

switched on.

- Check the fuse in the vehicle.

GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY

GB / IE / CYGB / IE / CYGB / IE / CY

J Ensure that the electrical socket is easily

accessible so that you can pull the plug

quickly out of the socket if necessary.

J Do not carry out any modiﬁcations or repairs

to the product yourself. The LEDs cannot and

must not be replaced.

CAUTION! The protective surround to the

LEDs cannot be replaced. Dispose of the LED

work lamp if you discover cracks or signs of

fracture on the protective surround.

J Dispose of the product if the LED work lamp,

mains adapter or car adapter is damaged.

J Never connect the LED work lamp to a power

supply socket if the LED work lamp, power

lead or socket is damaged or the LED work

lamp has been dropped.

J Ensure that the power lead cannot become

damaged by sharp edges or hot objects.

Unwind all the lead completely before use.

J Keep easily ﬂammable materials away the

product. Never hang objects above the LED

work lamp or the mains adapter and never

cover them.

J Pull the mains adapter / plug out of the mains

socket / cigarette lighter socket when you are

not using the LED work lamp or before you

clean it. Do this as well if signs of a fault

develop during use or charging, e.g. smoke,

burning smell etc., or during a storm. When

doing this, pull directly on the mains

adapter / plug and not on the lead.

J Protect the product against heat, cold, strong

vibrations and impacts.

J Do not attach the hook

to hot objects. The

dead weight of the LED work lamp might

cause the hook to deform or bend out of shape.

Before use

Charging the LED work lamp

Note: You can charge the LED work lamp from

an ordinary domestic mains power outlet or from

the cigarette lighter socket in your vehicle.

Note: The fuse of the car adapter is replaceable.

The speciﬁcation must comply with information

given in the section “Technical Data”. The fuse

may only be replaced by a qualiﬁed electrician

(see Fig. A).

Tip: We recommend that you charge the LED

work lamp from an ordinary domestic mains

power outlet to avoid draining your vehicle’s

battery.

CAUTION! Do not connect the LED work lamp

to the cigarette lighter socket of your vehicle if the

vehicle battery is old or degraded. Failure to

observe this advice may result in your vehicle’s

engine not starting.

Note: To use the LED work lamp without an adapter,

you must ﬁrst charge the integral rechargeable

batteries. It takes between 4 and 6 hours to

charge the integral batteries. The rechargeable

batteries are permanently installed in the handle

of the LED work lamp.

Note: Charge the LED work lamp for

approximately 12 hours before ﬁrst use.

Note: Charge the LED work lamp at least once

a month, if it is to remain unused for an extended

period of time.

Note: If the LED work lamp has not been

charged for an extended period of time (approx.

2 months), you could ﬁnd that the integral

rechargeable batteries have entered a dormant

state. Charge and discharge the LED work lamp a

number of times in succession to reactivate the

integral rechargeable batteries.

j Switch oﬀ the LED work lamp during the

charging process (set the ON / OFF switch

to position 0).

j Remove the rubber protection cap from the

bottom of the LED work lamp.

j Insert the power output connection plug of

the mains adapter

or the car adapter

into the power input connection socket

the handle of the LED work lamp.

Note: During charging from a cigarette

lighter socket, ensure that the plug is always

completely inserted into the cigarette lighter

socket of the vehicle. Failure to observe this

advice may result in risk of ﬁre from

overheating.

j Insert the mains adapter

into a mains

socket or the car adapter

into the

cigarette lighter socket of your vehicle.

Note: The product has an overcharging

protection system. Nevertheless, you should

disconnect the LED work lamp from the mains

once the charging process is complete.

Note: The indicator LED

illuminates red

during the charging process. When the

charging process is complete, the indicator

LED

illuminates green. When the indicator

LED

illuminates green, pull the mains

adapter

out of the mains socket or the car

adapter

out of the cigarette lighter socket.

Disconnect the adapter from the LED work

lamp to prevent the batteries from

discharging themselves.

j Place the rubber protection cap back on the

power input connection socket

before you

LED Work Lamp

Proper use

The product is intended for providing illumination

in dry indoor rooms and in outdoor environments.

If used outdoors the mains adapter must be

protected from moisture and the weather. The

product is not intended for commercial use.

Description of parts and

features

Hook

Magnetic mount

Mains adapter

Car adapter (for cigarette lighter socket)

ON / OFF switch

Power input connection socket

Indicator LED

Technical data

Light bulb: 23 LEDs (white,

non-replaceable)

Light intensity : approx. 12,000 mcd

(millicandela)

Lamp rechargeable

batteries: 3 x AA NiMH, 1000 mAh

(not replaceable)

Charging time: approx. 4 to 6 hours

Burn time: approx. 4 hours (with fully

charged battery)

Lifespan of LEDs: approx. 20,000 hours

Protection class:

System of protection: IP44

Adapter:

Input: 230-240 V

50 Hz

Output: 6 V , 300 mA

Model: SD-6300

Protection class:

System of protection: IP20

Cigarette lighter:

Input: 12 V

Output: 12 V , 240 mA

Replaceable fuse: U5F, 250 V

, 350 mA,

ø 5 x 20 mm

Scope of delivery

1 LED work lamp

1 Mains adapter

1 Car adapter for cigarette lighter socket

1 Magnetic mount

1 Operating instructions

6 5

Z29618-BS

LED WORK LAMP

Operation and Safety Notes

ΛΑΜΠΑ-LED

Υποδείξεις χειρισμού και ασφαλείας

EMC

87697_GB-IE-CY.indd 1 1/15/2013 4:52:31 PM

1 2

Z29618-BS 1

Indice de contenidos

Pagina 1 - Z29618-BS

GR / CYGB / IE / CYGB / IE / CYGB / IE / CYGB / IE / CYGB / IE / CY GB / IE / CYGB / IE / CYGB / IE / CYprotective surround. Then hold th

Pagina 2

GR / CYGR / CYGR / CYGR / CYGR / CYέντονης ρύπανσης, χρησιμοποιήστε ένα ελαφρά υγρό πανί.Q Απόρριψη Η συσκευασία αποτελείται αποκλειστ

Modelos relacionados 106341-14-01-BS

Mas documentos para Encendiendo Livarno Z29618-BS

a Ver el documento Livarno Z29618-BS Manual de usuario

Livarno Z29618-BS Manual de usuario (2 paginas)

Comentarios a estos manuales

Sin comentarios

Livarno Z29618-BS Manual de usuario

Busca en linea o descarga Manual de usuario para Encendiendo Livarno Z29618-BS. Livarno Z29618-BS User Manual Manual de usuario

Indice de contenidos

Modelos relacionados 106341-14-01-BS

Mas documentos para Encendiendo Livarno Z29618-BS

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Livarno Z29618-BS